Installation of Qingdao Guest Pedestrian Passage System

The common faults and treatment methods of LmnEaIBA automatic door installed in the guest pedestrian passage system are as follows: Faults 1: Door fan is not moving 1, Door fan is not moving, first check whether there is power supply, if it is the reason of power failure, it is OK to connect the power supply. 2. Check whether the lifting wheel part of the door fan is falling off from the track. At this time, it should be repaired by a master. 3. Whether or not the movable door fan mops the ground, this phenomenon will make the door start very hard, the main controller will think that there are obstacles, so self-locking protection, so that the door fan stop moving. 4. Check whether the induction automatic door is equipped with "safe light". Dust cover on the receiver of the safe light will also cause misoperation, which makes the main control of the automatic door mistakenly believe that there are objects, thus stopping closing the door, and dust should be cleaned up in time. Fault 2: The sound of automatic door switch is very loud: 1. The wheel of door and fan hanger is worn out for a long time. If it is only slightly worn, it can clean the track and wheel, and add a little lubricant to the wheel bearing. Note that it is not the track and plastic wheel, because it is easy to dust and damage the wheel after oil injection.


Installation of Guest Pedestrian Passage System
When checking the automatic door, the inspector can start by observing the door body. The inspectors carefully observe whether there are scratches on the threshold of the door body, the gap between the doors and leaves varies greatly, and whether the equipment has been corroded. These are the places that the inspectors need to examine carefully. Cleaning is the key to the normal operation of automatic doors. Therefore, there should not be too much dust and waste near the automatic door, which will affect the normal use of the automatic door. At the same time, regular cleaning of automatic doors will effectively extend the service life of automatic doors. In addition, whether it is cleaning or repairing the automatic door, inspectors must remember to turn off the power first, so as to clean safely. When the automatic door is running, it is very important to coordinate the components of the automatic door. If the automatic door wants to switch, it will use the ground wheel. Therefore, for these things, inspectors must carry out long-term maintenance and regular inspection, can not let the automatic door failure hidden danger, this can also avoid automatic rust stains.


Installation of Guest Pedestrian Passage System
According to the way of opening and closing, it can be divided into sliding door, flat door, folding door and revolving door. Push-pull doors can be subdivided into single open, overlapping single open, overlapping and arc doors. When the arc door and fan move smoothly along the arc track, it can be divided into half-arc unidirectional, half-arc bi-directional and full-arc bi-directional. In order to expand the flow of people to a limited extent, some push-pull automatic doors can be manually opened after the opening end point and the fixed door fan coincide, so as to achieve the width of import and export. The revolving door can also be subdivided into centric axis revolving door, circular guide suspended revolving door and central display area revolving door. Flat door can be subdivided into single one-way, double one-way, single two-way, double two-way. Folding doors can also be subdivided into two folding doors and four folding doors. According to the door material can be divided into safety glass (tempered glass, filament glass, laminated glass, titanium glass) revolving door, stainless steel decorative revolving door, building aluminium alloy profile, color coated steel plate, wood, etc., at the same time you can also use other suitable door material such as copper. Common types of glass automatic doors are framed glass automatic doors, stainless steel glass automatic doors and aluminium alloy framed glass automatic doors (planing or fluorocarbon spray paint).
Classification of automatic doors: 1. According to the form of opening and closing: can be divided into sliding doors, flat doors, overlapping doors, folding doors, arc doors and revolving doors. (1) Push and pull doors: can be subdivided into single open, overlapping single open, overlapping and arc doors. The arc door and fan move smoothly along the solitary track, which can be divided into half-arc unidirectional, half-arc bi-directional and full-arc bi-directional. In order to widen the entrance range to a limited extent, some push-pull (nested) automatic doors can be made into a manual flat opening after the opening end coincides with the fixed fan, which is also summarized as push-pull automatic doors. (2) Rotary door: can be subdivided into central axis type, circular guide suspension type and central display area type. (3) Flat open door: can be subdivided into single one-way, double one-way, single two-way and double two-way. (4) Folding door: It can be subdivided into 2 folding doors and 4 folding doors. (5) Emergency evacuation automatic door: movable fan and fixed fan can be opened 90 degrees flat. (6) Overlapping doors: can be divided into overlapping automatic doors with fixed side pages and overlapping automatic doors without fixed side pages (7) arc doors: can be divided into arc segments, semi-circle, full circle, with fixed door pages, or without fixed door pages, arc can be set according to specific case design, application is very flexible, and different arc splicing can be used to construct beautiful and changeable geometry. As a result, Caesar's arc door will be used more and more widely.


But such an outcome is not only the misfortune of the whole industry, but also the misfortune of the users of the industry. Because maybe a lot of users install the products of this enterprise soon, the enterprise will collapse, how will the maintenance of its products continue? Finally, the end result of the development of the industry is the lessons learned from the previous color TV industry and mobile phone industry. After a big circle, the whole industry returns to its origin. What the big waves leave behind is those powerful international enterprises that focus on products and user services and a small number of domestic new-generation enterprises that focus on independent innovation and honest and legal operation. Automatic doors have become more and more popular. Many shopping malls and hotels will choose automatic doors to increase the company's image. The function of ordinary door is mainly to enter and exit, and automatic door is in addition to this function.